VERIFIED
When a Bosch dishwasher shows E0105, the source record points to heater electronics fault detected during self-test. Use symptoms and model-specific checks to decide when service is needed.
Code E0105 on this Bosch dishwasher family is tied to heater electronics fault detected during self-test. The useful question is not only what the code says, but also what happened immediately before it appeared and whether the condition returns.
Start with external observations rather than parts guessing. The goal is to confirm the conditions around the warning without bypassing safety devices or turning a diagnostic code into an unsupported DIY repair procedure.
At a glance
- Code: E0105
- Appliance: Bosch Dishwasher
- Verified meaning: heater electronics fault detected during self-test
- Diagnostic direction: the heating or temperature-control path
- Service area context: San Francisco; confirm coverage by ZIP code
Meaning of the display
The technical anchor for E0105 is heater electronics fault detected during self-test. That description should remain unchanged when the page is imported. What can vary is the hardware behind the condition, so the model/E-Nr and the observed behavior are necessary context.
For this reason, E0105 should be used to narrow the troubleshooting path toward the heating or temperature-control path, not as automatic proof that one specific component has failed.
What can happen when the code is active
Before changing settings or cycling power, note what the appliance is doing. Useful observations include:
- Water might not heat as expected.
- Drying performance can change.
- The cycle might pause or end early.
- The code can return after a restart.
What may be behind the warning
- Heater or heat-pump heating fault.
- Temperature/heating control fault.
- Wiring or electronic switching fault in the heating path.
Owner-level checks that stay external
- Write down the code and full E-Nr/model number.
- If Bosch permits a normal breaker reset for this code, switch power off for about 30 seconds and restore it once.
- Avoid test the heater, live wiring, or control board from inside the appliance.
These steps are meant to gather useful information without exposing live wiring, bypassing an interlock, defeating a leak-protection device, or opening a system the owner documentation does not designate for user access.
When continued operation is a bad idea
Keep the dishwasher off if there is overheating, electrical odor, smoke, or repeated power interruption.
When external checks are no longer enough
If the same warning reappears, internal heating, sensing, wiring, and control components need model-aware testing. When requesting service, include the complete Bosch model/E-Nr. Similar-looking dishwashers can use different controls, pumps, drying systems, and diagnostic logic.
A useful service request includes the exact display, what the appliance was doing immediately before the warning, and which external checks were already completed.
Why the model number matters
Use the complete Bosch model/E-Nr when matching E0105 to technical documentation. Similar-looking products can use different sensors, controls, pumps, motors, or diagnostic logic.
FAQ
For the source record used here, E0105 is associated with heater electronics fault detected during self-test. The complete model/E-Nr still matters because Bosch can use different hardware and diagnostic logic across product families.
Do not continue if the warning is accompanied by the stop conditions listed above. Water near electrical parts, leaking, smoke, a burning odor, sparking, or repeated breaker trips are reasons to leave the appliance off and arrange service.
Where the Bosch documentation for the exact model allows a normal power reset, use it once after recording the code. A returning warning means the underlying condition still needs attention; repeated resets are not a repair.
Not necessarily. An error code narrows the detected condition or system. The model number, symptoms, and model-specific testing are still needed before selecting a component.
Have the full Bosch model/E-Nr, the exact E0105 display, the cycle stage or operating state when it appears, the visible symptoms, and the safe checks already completed.
Bosch service in the San Francisco area
Need model-specific diagnosis for E0105?
If E0105 remains active or returns, request Bosch dishwasher diagnosis for the San Francisco service area. Include the complete model/E-Nr, the exact code, a short symptom description, and your ZIP code so service coverage can be confirmed.
Model compatibility: Bosch reuses codes across series and model years, so Bosch Dishwasher E0105 Error Code may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.