VERIFIED
Flashing Clean Lights narrows attention to door-sensor circuit fault on the applicable Bosch dishwasher platform. Keep the full model number with the code for accurate diagnosis.
When Flashing Clean Lights appears on a Bosch dishwasher, the control has registered door-sensor circuit fault. That points the diagnostic process toward the door, latch, or locking system, but the display alone is not enough to choose a replacement part.
Treat the code as evidence, not a complete diagnosis. Record what the appliance does, complete only the safe checks that fit the exact model, and arrange testing if the warning remains active or comes back.
At a glance
- Code: Flashing Clean Lights
- Appliance: Bosch Dishwasher
- Verified meaning: door-sensor circuit fault
- Diagnostic direction: the door, latch, or locking system
- Service area context: San Francisco; confirm coverage by ZIP code
What the code is pointing to
The technical anchor for Flashing Clean Lights is door-sensor circuit fault. That description should remain unchanged when the page is imported. What can vary is the hardware behind the condition, so the model/E-Nr and the observed behavior are necessary context.
For this reason, Flashing Clean Lights should be used to narrow the troubleshooting path toward the door, latch, or locking system, not as automatic proof that one specific component has failed.
Operating signs to record
Before changing settings or cycling power, note what the appliance is doing. Useful observations include:
- The cycle might refuse to start.
- The dishwasher can stop unexpectedly.
- The controls can indicate that the door is not in the expected state.
- The code can come back even when the door appears closed.
Possible causes
- Door not reaching the expected closed state.
- Door sensor or latch-circuit fault.
- Wiring or control fault in the door-sensing path.
First checks to make safely
- Confirm no rack, utensil, or dish prevents the door from closing fully.
- Look over the latch area externally for obvious debris without removing panels.
- Perform one normal power reset if Bosch specifies it for the code.
These steps are meant to gather useful information without exposing live wiring, bypassing an interlock, defeating a leak-protection device, or opening a system the owner documentation does not designate for user access.
When to stop using the appliance
If the door closes normally but the code returns, the sensor, latch circuit, wiring, or control path requires model-specific diagnosis. When requesting service, include the complete Bosch model/E-Nr. Similar-looking dishwashers can use different controls, pumps, drying systems, and diagnostic logic.
If the code comes back
If the door closes normally but the code returns, the sensor, latch circuit, wiring, or control path requires model-specific diagnosis. When requesting service, include the complete Bosch model/E-Nr. Similar-looking dishwashers can use different controls, pumps, drying systems, and diagnostic logic.
A useful service request includes the exact display, what the appliance was doing immediately before the warning, and which external checks were already completed.
Use the complete Bosch E-Nr
Use the complete Bosch model/E-Nr when matching Flashing Clean Lights to technical documentation. Similar-looking products can use different sensors, controls, pumps, motors, or diagnostic logic.
FAQ
For the source record used here, Flashing Clean Lights is associated with door-sensor circuit fault. The complete model/E-Nr still matters because Bosch can use different hardware and diagnostic logic across product families.
Do not continue if the warning is accompanied by the stop conditions listed above. Water near electrical parts, leaking, smoke, a burning odor, sparking, or repeated breaker trips are reasons to leave the appliance off and arrange service.
Where the Bosch documentation for the exact model allows a normal power reset, use it once after recording the code. A returning warning means the underlying condition still needs attention; repeated resets are not a repair.
Not necessarily. An error code narrows the detected condition or system. The model number, symptoms, and model-specific testing are still needed before selecting a component.
Have the full Bosch model/E-Nr, the exact Flashing Clean Lights display, the cycle stage or operating state when it appears, the visible symptoms, and the safe checks already completed.
Bosch service in the San Francisco area
Still seeing Flashing Clean Lights on your Bosch dishwasher?
If Flashing Clean Lights remains active or returns, request Bosch dishwasher diagnosis for the San Francisco service area. Include the complete model/E-Nr, the exact code, a short symptom description, and your ZIP code so service coverage can be confirmed.
Model compatibility: Bosch reuses codes across series and model years, so Bosch Dishwasher Flashing Clean Lights Error Code may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.