Skip to content
Blog

Bosch Heat-Pump Dryer Says the Water Tank Is Full After You Empty It

A heat-pump dryer showing a full water tank after you emptied it may have a seating, filter or drain-hose issue. Check these first.

If a Bosch heat-pump dryer still says the water tank is full after you have emptied it, the usual causes are a container that is not seated fully, a blocked lint filter that has stopped the water draining properly, or a kinked drain hose on a model plumbed to drain. Empty it again, seat it firmly, clean the filters, and watch whether the message returns on the next cycle.

Where the water goes in a condensation or heat-pump dryer

These dryers pull moisture from the clothes as water rather than sending steam out through a duct. That water has to go somewhere: into a removable container, or, if you have plumbed it, down a drain hose. The WTW87NH1UC, a 500 Series 24-inch compact heat pump dryer, lists heat-pump technology and a 4.0 cu. ft. drum, and the WPA12100UC, a 300 Series 24-inch compact condensation dryer, lists condensation drying that requires no exhaust duct. In both, a message about full water means the machine thinks the water has nowhere to go.

Seating the container properly

Pull the container out and empty it completely, including any water that sits in the corner when you tilt it. Check it for cracks and for debris at the outlet. Push it back until you feel it seat. A container that sits a few millimetres off can leave the sensor believing it is full, or can leave the water path misaligned so water spills over. Wipe the compartment where the container sits so nothing prevents it sliding home.

Filters and lint: why a clogged filter fills the tank

Bosch lists E01 as a fluff (lint) filter blocked with lint or fabric softener residue, and E02 as the fluff filter blocked too, with the step of cleaning the lint filter after each drying cycle. Residue from fabric softener is a particular culprit because it coats the mesh in a film you may not spot. Wash the filter with warm water and a soft brush, let it dry, and refit it. On models with a condenser that rinses lint automatically during cycles, such as the WQB245B0UC, listed at 4.0 cu. ft. with an automatically rinsed condenser, lint can still collect elsewhere, so check every place the manual names.

The drain hose: E03 and kinks

The Bosch dryer message closest to this symptom is E03, listed as a condensation drainage hose that is blocked or kinked, with the step of checking that the hose is installed without kinks. Other dryer messages, such as E12, have their own pages on our site. If your dryer drains to a sink or standpipe, trace the hose from the machine to the drain. Look for a bend behind the dryer, a hose pinched under the machine, or a hose end that sits below the level of the drain connection. Straighten it and run a cycle.

Empty the container after every cycle rather than waiting for the message, because a full container left standing can grow slimy and leave residue at the outlet. Rinse it now and then with warm water. Keep the area around the dryer free of boxes so the drain hose is never squeezed, and avoid overloading the drum, since a packed load dries slowly and sends more water to the container per cycle than a moderate one. If you notice that the message only appears after large towel loads, tell us, because that is a different story from a message that appears every time.

What a message that returns tells you

What you did If the message goes If it returns
Emptied and reseated the container Seating was the cause Move on to the filter
Cleaned the lint filter Residue was blocking flow Check the drain hose
Straightened the drain hose The hose was restricting water Sensor or pump needs testing

What owner checks cannot reveal

If the container is seated, the filters are clean and the hose runs freely, the problem has moved to parts you cannot see. A level sensor can misread, a pump can stop moving water, or a passage inside the machine can be blocked. Each of those needs the cover off and a meter. Do not remove panels yourself, and do not run the dryer repeatedly with the message on, since a machine that cannot clear its water may keep damp air trapped inside.

Water-path testing and what to tell us at booking

We check the container and its seat, trace water from the drum to the drain, test the level sensor and pump, inspect the filters and condenser path, and read any stored fault. Our dryer repair page and dryer information page describe the service. Give us the model and serial number from the rating label, whether the dryer drains to the container or a hose, how soon after emptying the message returns, what the load was, and any message exactly as displayed.

FAQ

Need help with a Bosch appliance?

Book a specialist visit for a clear estimate and approval before any repair.

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair