Skip to content
Error Code

Bosch Dryer E12 Error Code

Source: Bosch US Owner Support - Dryer Error Codes

Error code E12
Appliance Dryer
Quick answer

E12 means the dryer is overheating, potentially because airflow is restricted. Clean the lint screen and check the outside vent.

E12 needs a technician on site

E12 points to overheating / fluffing level 2 — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

Bosch describes E12 as the dryer overheating, and it names the likely reason in the same sentence: restricted airflow. A vented dryer pushes hot, damp air out through the lint screen and the vent duct. When that path narrows, heat builds up inside the cabinet faster than it can leave, and the dryer shows E12.

At a glance

Code E12
Appliance Dryer
What it means E12 on a Bosch dryer means the dryer is overheating, potentially due to restricted airflow.
First thing to try Turn the dryer off and let it cool. Parts near the heater and the drum can be hot right after an overheat.

Where airflow gets choked

Bosch points to two places, one inside and one outside the house:

  • The lint screen. Lint collects on it every load. A screen that has not been cleaned, or that has a coating on the mesh, holds back the air.
  • The external dryer vent. Bosch asks you to confirm the vent is not obstructed, bent, or blocked at the point where it exits your home.

Clearing E12 step by step

  1. Turn the dryer off and let it cool. Parts near the heater and the drum can be hot right after an overheat.
  2. Take out the lint screen and clean it thoroughly. Rinse it with warm water if the mesh looks dull or clogged.
  3. Go outside and find the vent hood where the duct leaves the building. Remove lint, leaves, nests or anything else blocking the flap, and make sure the flap opens freely.
  4. Behind the dryer, check that the duct is not crushed, kinked or sharply bent where the machine was pushed back.
  5. Reset the dryer the way Bosch describes for any code: unplug it or switch off its breaker for at least five minutes, then restore power.
  6. Run a short timed cycle and check that air is coming out at the outside vent.

The high-limit reset button

Bosch notes that many models have a red reset button on the high-limit thermostat behind the rear panel. The high-limit thermostat is a safety device that cuts the heat when the dryer runs too hot. Reaching it means opening the cabinet near the heater, so leave it to a technician.

When to stop troubleshooting

If E12 returns after the screen and vent are clear, or the vent run is inside a wall or roof you cannot reach, call for service. A technician can check the full duct run and the heating safety parts.

Related codes

  • E01: lint filter blocked, the same screen that E12 starts with
  • E63: a heating element problem rather than an airflow one
  • E06: heating-circuit fault, which Bosch leaves to a technician

San Francisco Bosch dryer overheating service

If E12 keeps coming back, call (415) 851-9513. Let us know where the vent exits the building and whether you have already cleaned it.

Plain language

What this code means

E12 on a Bosch dryer means the dryer is overheating, potentially due to restricted airflow.

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair