Skip to content
Error Code

Bosch Range F170 Error Code

Source: Appliance Helpers - Bosch Range Error Codes

Error code F170
Appliance Range
Quick answer

Bosch range F170 is linked with power failure detected. Review the visible symptoms, model details, and safe external checks before deciding on the next step.

F170 needs a technician on site

F170 points to power failure detected — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

If F170 appears on a Bosch range, it means power failure detected. Product generations can differ internally, so the observed behavior and model/E-Nr matter before the code is interpreted too narrowly.

At a glance

Code F170
Appliance Range
What it means If F170 appears on a Bosch range, it means power failure detected. Product generations can differ internally, so the observed behavior and model/E-Nr matter before the code is interpreted too narrowly.Start with external observations and manufacturer-approved owner

Start with external observations and manufacturer-approved owner checks only. If the code persists, move to model-specific diagnosis rather than repeated resets or speculative part replacement. This message concerns the power reaching the control, which can come from inside the range or from the household supply.

At a glance

  • Code: F170
  • Appliance: Bosch Range
  • Verified meaning: power failure detected
  • Primary diagnostic direction: the electronic control path
  • Service-area context: San Francisco; confirm coverage by ZIP code

What the control is reporting

F170 means power failure detected. The warning narrows the diagnostic path toward the electronic control path, while the exact model and symptom sequence determine how that information should be applied.

A power failure detected is a statement about supply seen by the control, not about a single component. Whether the household supply, the range’s connection, or its internal supply is involved is what diagnosis has to establish.

What can happen while the code is active

Before changing settings or cycling power, record the behavior you can see or hear:

  • The appliance may fail to start normally.
  • A cycle may reset or stop.
  • Other controls can behave intermittently.
  • The code may appear after a supply interruption.

What may be causing it

Diagnosis may need to consider the following possibilities without treating any single one as confirmed:

  • Incoming voltage outside the expected range.
  • A loose or damaged electrical connection.
  • An internal power-supply or conversion fault.
  • A control board detecting unstable power.
  • A supply interruption or instability seen by the control.

What you can verify externally

  • Write down whether other household lights or appliances are behaving abnormally.
  • Reset a tripped breaker only once and only when there is no sign of damage.
  • Avoid measure or modify household wiring unless you are qualified to perform electrical work.

These checks are for information gathering only. Do not expose live wiring, bypass an interlock, defeat leak protection, open a sealed refrigeration circuit, or use undocumented service-mode procedures.

When continued operation is not appropriate

Leave the appliance off for repeated breaker trips, sparking, burning odor, or visible wiring damage.

When external checks are no longer enough

If the same warning reappears, the supply should be verified before appliance components are replaced; internal power electronics may then require diagnosis. Do not choose the most expensive module from the code alone. The technician should verify the relevant circuit or mechanism before recommending a repair.

For a service request, include what the appliance was doing immediately before the warning and which safe checks were already completed.

Why the full Bosch model/E-Nr matters

The complete rating-label model matters. A code meaning documented on one Bosch range platform should not be assumed to apply to every generation without verification. The E-Nr shows how this model’s control monitors incoming power.

FAQ

Bosch service in the San Francisco area

Need model-specific diagnosis for F170?

If F170 remains active or comes back, request Bosch range diagnosis for the San Francisco service area. Include the complete model/E-Nr, exact code, symptom summary, and ZIP code so service coverage can be confirmed.

Plain language

What this code means

If F170 appears on a Bosch range, it means power failure detected. Product generations can differ internally, so the observed behavior and model/E-Nr matter before the code is interpreted too narrowly.Start with external observations and manufacturer-approved owner

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair