Skip to content
Error Code

Bosch Dishwasher Flashing Active and Clean Lights

Source: Bosch US Owner Support - Dishwasher Error Codes

Appliance Dishwasher
Quick answer

When a Bosch dishwasher shows Flashing Active + Clean Lights, the code points to drainage restriction involving the pump area, hose, or external drain path. Use symptoms and model-specific checks to decide when service is needed.

When Flashing Active + Clean Lights appears on a Bosch dishwasher, the control has registered drainage restriction involving the pump area, hose, or external drain path. That points the diagnostic process toward the drain path or water-removal system, but the display alone is not enough to choose a replacement part. For this light pairing, the drain meaning applies when the model/E-Nr matches the documentation, since other flashing combinations can point elsewhere.

Start with external observations rather than parts guessing. The goal is to confirm the conditions around the warning without bypassing safety devices or turning a diagnostic code into an unsupported DIY repair procedure.

At a glance

  • Code: Flashing Active + Clean Lights
  • Appliance: Bosch Dishwasher
  • Verified meaning: drainage restriction involving the pump area, hose, or external drain path
  • Diagnostic direction: the drain path or water-removal system
  • Service area context: San Francisco; confirm coverage by ZIP code

What the code is pointing to

Flashing Active + Clean Lights means drainage restriction involving the pump area, hose, or external drain path. What can vary is the hardware behind the condition, so the model/E-Nr and the observed behavior are necessary context.

For this reason, Flashing Active + Clean Lights should be used to narrow the troubleshooting path toward the drain path or water-removal system, not as automatic proof that one specific component has failed.

The air gap and disposal connection are the parts of the drain route that sit outside the dishwasher cabinet. They are worth looking at first because a blockage there leaves the pump working normally while the water still cannot leave.

Operating signs to record

Before changing settings or cycling power, note what the appliance is doing. Useful observations include:

  • Standing water can remain in the tub.
  • Draining can sound slower or different.
  • The program might stop before completion.
  • Water in the tub can still be visible at the start of the next cycle.
  • The code can return at the drain stage.

Possible causes

Diagnosis may need to consider the following possibilities without assuming any one of them is confirmed:

  • Blocked filter or pump area.
  • Kinked or obstructed drain hose.
  • Blocked air gap or disposal connection.
  • Drain-pump or sensing fault.

First checks to make safely

  • Turn the dishwasher off before user-accessible drain maintenance.
  • Clean the removable filter if the model manual identifies it as a user-maintenance part.
  • Verify the accessible pump-cover area only as described in the owner instructions.
  • Look over the external drain hose for a sharp kink and check the air gap or disposal connection for an obvious blockage.

These steps are meant to gather useful information without exposing live wiring, bypassing an interlock, defeating a leak-protection device, or opening a system the owner documentation does not designate for user access. If those visible parts are clear, that narrows the restriction to the pump or the internal drain path rather than ruling the code out.

When to stop using the appliance

If the accessible drain path is clear and the code returns, the pump, sensing, wiring, installation, or internal drain path requires model-specific diagnosis. When requesting service, include the complete Bosch model/E-Nr. Similar-looking dishwashers can use different controls, pumps, drying systems, and diagnostic logic.

If the code comes back

A useful service request includes the exact display, what the appliance was doing immediately before the warning, and which external checks were already completed.

Use the complete Bosch E-Nr

Use the complete Bosch model/E-Nr when matching Flashing Active + Clean Lights to technical documentation. Similar-looking products can use different sensors, controls, pumps, motors, or diagnostic logic.

FAQ

Bosch service in the San Francisco area

Still seeing Flashing Active + Clean Lights on your Bosch dishwasher?

If Flashing Active + Clean Lights remains active or returns, request Bosch dishwasher diagnosis for the San Francisco service area. Include the complete model/E-Nr, the exact code, a short symptom description, and your ZIP code so service coverage can be confirmed.

Plain language

What this code means

When Flashing Active + Clean Lights appears on a Bosch dishwasher, the control has registered drainage restriction involving the pump area, hose, or external drain path. That points the diagnostic process toward the drain path or water-removal system, but the

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair