Skip to content
Error Code

Bosch Dishwasher Flashing Clean and Sanitized Lights

Source: Bosch US Owner Support - Dishwasher Error Codes

Appliance Dishwasher
Quick answer

Flashing Clean + Sanitized Lights narrows attention to internal heat-pump heater fault on the applicable Bosch dishwasher platform. Keep the full model number with the code for accurate diagnosis.

Flashing Clean and Sanitized Lights needs a technician on site

Flashing Clean and Sanitized Lights points to internal heat-pump heater fault — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

If your Bosch dishwasher displays Flashing Clean + Sanitized Lights, the verified reference for this record is internal heat-pump heater fault. Because Bosch platforms can differ by generation, keep the complete model number with the code before making repair decisions. Heat-pump models handle heating and drying differently from a plain heating element, which is one reason the exact E-Nr is needed before a heating code is read on any particular dishwasher.

The guidance below stays at the owner-safe level: observe the symptom, check only accessible items supported by the model documentation, and stop before opening protected electrical, water, gas, or mechanical systems.

At a glance

  • Code: Flashing Clean + Sanitized Lights
  • Appliance: Bosch Dishwasher
  • Verified meaning: internal heat-pump heater fault
  • Diagnostic direction: the heating or temperature-control path
  • Service area context: San Francisco; confirm coverage by ZIP code

What Bosch is detecting

Flashing Clean + Sanitized Lights means internal heat-pump heater fault. What can vary is the hardware behind the condition, so the model/E-Nr and the observed behavior are necessary context.

For this reason, Flashing Clean + Sanitized Lights should be used to narrow the troubleshooting path toward the heating or temperature-control path, not as automatic proof that one specific component has failed.

The two lights flashing together are what tie this display to the heater fault. A different pairing is a different display, and it should be matched to the documentation separately.

What you may notice

Before changing settings or cycling power, note what the appliance is doing. Useful observations include:

  • Water can fail to heat as expected.
  • The wash can run with water that stays cooler than the selected program calls for.
  • Drying performance can change.
  • The cycle can pause or end early.
  • The code can return after a restart.

Systems and conditions to consider

Diagnosis may need to consider the following possibilities without assuming any one of them is confirmed:

  • Heater or heat-pump heating fault.
  • Temperature/heating control fault.
  • Wiring or electronic switching fault in the heating path.

What you can verify without opening the appliance

  • Write down or photograph the exact code.
  • Record the complete Bosch model/E-Nr.
  • Follow only owner-manual checks that do not require panel removal or access to live parts.

These steps are meant to gather useful information without exposing live wiring, bypassing an interlock, defeating a leak-protection device, or opening a system the owner documentation does not designate for user access. A heating fault is separated from a sensing fault by comparing what the control commands with what the sensor reports, and that testing belongs to the service visit.

Leave the appliance off if

Keep the dishwasher off if there is overheating, electrical odor, smoke, or repeated power interruption.

When the next step is diagnosis

If the same warning reappears, internal heating, sensing, wiring, and control components need model-aware testing. When requesting service, include the complete Bosch model/E-Nr. Similar-looking dishwashers can use different controls, pumps, drying systems, and diagnostic logic.

A useful service request includes the exact display, what the appliance was doing immediately before the warning, and which external checks were already completed.

Model and platform note

Use the complete Bosch model/E-Nr when matching Flashing Clean + Sanitized Lights to technical documentation. Similar-looking products can use different sensors, controls, pumps, motors, or diagnostic logic.

FAQ

Bosch service in the San Francisco area

Ready to have Bosch Flashing Clean + Sanitized Lights checked?

If Flashing Clean + Sanitized Lights remains active or returns, request Bosch dishwasher diagnosis for the San Francisco service area. Include the complete model/E-Nr, the exact code, a short symptom description, and your ZIP code so service coverage can be confirmed.

Plain language

What this code means

If your Bosch dishwasher displays Flashing Clean + Sanitized Lights, the verified reference for this record is internal heat-pump heater fault. Because Bosch platforms can differ by generation, keep the complete model number with the code before making repair decisions.The

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair