Skip to content
Error Code

Bosch Range F113 Error Code

Source: Appliance Helpers - Bosch Range Error Codes

Error code F113
Appliance Range
Quick answer

Bosch range F113 is linked with runaway oven temperature at a very high safety threshold while latched. Review the visible symptoms, model details, and safe external checks before deciding on the next step.

F113 needs a technician on site

F113 points to runaway oven temperature at a very high safety threshold while latched — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

If F113 appears on a Bosch range, it means runaway oven temperature at a very high safety threshold while latched. Product generations can differ internally, so the observed behavior and model/E-Nr matter before the code is interpreted too narrowly.

At a glance

Code F113
Appliance Range
What it means If F113 appears on a Bosch range, it means runaway oven temperature at a very high safety threshold while latched. Product generations can differ internally, so the observed behavior and model/E-Nr matter before the code is interpreted

Treat the warning as evidence, not a complete repair instruction. Do not bypass interlocks, leak protection, electrical safeguards, or sealed systems just to clear the display. Latched means the control is holding the condition, not reporting a momentary reading.

At a glance

  • Code: F113
  • Appliance: Bosch Range
  • Verified meaning: runaway oven temperature at a very high safety threshold while latched
  • Primary diagnostic direction: the heating and temperature-control system
  • Service-area context: San Francisco; confirm coverage by ZIP code

What the control is reporting

F113 means runaway oven temperature at a very high safety threshold while latched. The warning narrows the diagnostic path toward the heating and temperature-control system, while the exact model and symptom sequence determine how that information should be applied.

An oven holds temperature by switching heat on and off against its sensor reading. A runaway reading points at that regulation loop: sensor, heat switching, and the control that interprets both.

What can happen while the code is active

Before changing settings or cycling power, record the behavior you can see or hear:

  • The appliance may refuse to start.
  • A cycle may stop unexpectedly.
  • The door can remain locked or fail to lock.
  • The control can fail to recognize the expected door position.

What may be causing it

Diagnosis may need to consider the following possibilities without treating any single one as confirmed:

  • The door not reaching its expected position.
  • A damaged latch, hook, or lock mechanism.
  • A door sensor or switch fault.
  • Wiring or electronic control failure in the interlock path.
  • A heat-switching or regulation problem that lets heating continue past the set point.

What you can verify externally

  • Confirm clothing, cookware, or another object is not preventing normal closure.
  • Look over the visible latch area for obvious debris or physical damage.
  • Avoid force a locked door and do not bypass the interlock.

These checks are for information gathering only. Do not expose live wiring, bypass an interlock, defeat leak protection, open a sealed refrigeration circuit, or use undocumented service-mode procedures.

When continued operation is not appropriate

Do not continue operating an appliance with a door that cannot latch securely or with a defeated safety interlock.

When external checks are no longer enough

A returning door code with normal external alignment requires testing of the lock/switch, wiring, and model-specific control path. If the warning is intermittent, note the program, temperature, load, or operating stage that makes it return. That pattern can narrow diagnosis considerably.

For a service request, include what the appliance was doing immediately before the warning and which safe checks were already completed.

Why the full Bosch model/E-Nr matters

Use the exact Bosch model number when booking. It is the safest way to connect F113 with the correct technical documentation and related parts. For a heat-related latch, the E-Nr identifies the oven and control generation involved.

FAQ

Bosch service in the San Francisco area

Need model-specific diagnosis for F113?

If F113 remains active or comes back, request Bosch range diagnosis for the San Francisco service area. Include the complete model/E-Nr, exact code, symptom summary, and ZIP code so service coverage can be confirmed.

Plain language

What this code means

If F113 appears on a Bosch range, it means runaway oven temperature at a very high safety threshold while latched. Product generations can differ internally, so the observed behavior and model/E-Nr matter before the code is interpreted

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair