Skip to content
Error Code

Bosch Range E302 / e302 Error Code

Source: Bosch US Owner Support - Freestanding Ranges Error Codes

Error code E302 / e302
Appliance Range
Quick answer

Letter case matters: E302 is an overheated control panel with owner steps; e302 is an overheated power board that needs service.

E302 / e302 needs a technician on site

E302 / e302 points to control module too hot — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

Bosch’s freestanding range list uses the number 302 twice, and only the letter case tells them apart. A capital E302 means the control panel has overheated. A lowercase e302 means the power board has overheated. Both versions appear on the electric and the gas lists. One comes with owner steps; the other does not.

At a glance

Code E302 / e302
Appliance Range
What it means Uppercase E302 means the control panel has overheated; lowercase e302 means the power board has overheated.

Reading the display

E302 (capital) e302 (lowercase)
Part that overheated Control panel Power board
Owner steps from Bosch Room and pot check, cool-down, breaker reset None
Bosch’s direction Service only if it persists Book a visit

Capital E302: the control panel

The control panel is the display and keys you use to run the range. Bosch’s checklist for it starts with the kitchen, not the range:

  1. Check how warm the room is.
  2. Look at where the pots are. Bosch says pot position can affect the temperature on the control panel.
  3. Let the range cool down.
  4. Switch it off at the circuit breaker and leave it off for five minutes.
  5. Turn the breaker back on.

Bosch notes that pot position can affect the control panel temperature, so try repositioning large pots. If it persists after the reset, Bosch says to book service.

Lowercase e302: the power board

The power board is the circuit board inside the range that switches power to the range’s heating parts. Bosch lists no owner check for e302 at all and goes straight to booking a service visit. Because the board sits inside the cabinet, the room and pot checks above do not apply. Leave the range off at the breaker rather than restarting it again and again.

What to tell a technician

  • Whether the display shows a capital E or a lowercase e.
  • How warm the kitchen was and which zones or pots were in use.
  • Whether the five-minute breaker reset cleared the code, and for how long.

Questions about E302 and e302

Can a hot kitchen cause the lowercase version? Bosch only links room temperature and pot position to the capital E302. For e302, it gives no cause and no owner step.

The display font makes the letter hard to read. What then? Trying the capital E302 steps once does no harm. If the code is back right away on a cool range, stop there and arrange service.

Other range codes in this area

  • e005: the user interface and power board lost communication
  • e011: a touch sensor failure on the oven control panel
  • e310: a power supply failure

Bosch range repair in San Francisco

For e302, or a capital E302 that keeps returning, call (415) 851-9513. Tell us whether the E is upper or lower case and what you have already tried.

Plain language

What this code means

Uppercase E302 means the control panel has overheated; lowercase e302 means the power board has overheated.

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair