Skip to content
Error Code

Bosch Wall Oven E000 Error Code

Source: Service Manual for 300, 500 and 800 Series Built-in Wall Ovens (Bosch HBL8x50UC, HBL57x0UC, HBL56x0UC, HBL54x0UC, HBL35x0UC, HBL33x0UC, HBN56x0UC, HBN54x0UC, HBN35x0UC, HBN34x0UC, HBN3350UC), section 5.1 Error Code Table

Error code E000
Appliance Oven
Quick answer

E000 means the oven's control module and user interface are mismatched. Bosch's service manual resolves it by setting the correct Option Code in Service Mode.

E000 needs a technician on site

E000 points to wrong module code — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

E000 is the “wrong module combination” code on Bosch built-in wall ovens covered by Bosch’s service manual for the 2007 300, 500 and 800 Series (HBL and HBN models). The oven has two main electronic parts: the user interface, which carries the display and controls, and the PC control module, the relay board that switches the elements, fans, lights and door latch. When those two do not agree on what oven they are installed in, the display shows E000 at start-up.

At a glance

Code E000
Appliance Oven
What it means The control module and the user interface are a mismatched combination, so the Option Code must be set correctly.

Where E000 usually comes from

Bosch’s manual is specific here. When both the user interface board and the control module have been replaced, the oven will display E000 when it powers up. The fix the manual gives is to put the unit in Service Mode and set the Option Code by hand. So if you see this code shortly after a repair that involved new electronics, that history matters more than anything you can inspect yourself.

What the Option Code is

Each model family has its own 4-digit Option Code, listed in Bosch’s service manual. The manual says the code is printed on a label near the PC control board in the upper plenum, and it also lists the codes in a table:

Model Option Code Model Option Code
HBL33 0150 HBL86 0951
HBL34 0250 HBL87 0351
HBL35 0750 HBN33 0140
HBL54 0351 HBN34 0240
HBL56 0851 HBN35 0740
HBL57 0351 HBN54 0341
HBL84 0351 HBN56 0841

Who should clear it

Setting the code is part of a service procedure: entering Service Mode with a model-specific key sequence, entering the code, then resetting the oven by cutting power at the breaker for 30 seconds and setting the time and date again. The manual ends that procedure with a reminder to confirm the error is gone and the oven works normally. That job belongs to whoever installed the new boards. What you can usefully do is note your full model number and tell the technician the code appeared after a board replacement.

Quick answers on E000

Will turning the breaker off and on clear it?
The manual’s remedy is the Option Code. A 30-second power cut is only the final step of that procedure, after the code has been entered.

How do I find my exact model?
The data plate with the model and FD numbers is on the underside of the control panel. The first four positions of the FD number give the year and month the oven was built, and numbers starting with 87 date from 2007.

Codes that point the same direction

  • E005: the interface and control module stopped talking at start-up, a wiring or connection fault rather than a mismatch
  • E009: the interface did not receive all of its start-up data from the control module
  • E309: a memory check failure inside the control module itself

E000 wall oven service in San Francisco

If E000 appeared after electronics were replaced, call (415) 851-9513. The model and FD numbers are on the data plate under the control panel, and they let us confirm the right Option Code before the visit.

Plain language

What this code means

The control module and the user interface are a mismatched combination, so the Option Code must be set correctly.

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair