Skip to content
Error Code

Bosch Wall Oven E009 Error Code

Source: Service Manual for 300, 500 and 800 Series Built-in Wall Ovens (Bosch HBL8x50UC, HBL57x0UC, HBL56x0UC, HBL54x0UC, HBL35x0UC, HBL33x0UC, HBN56x0UC, HBN54x0UC, HBN35x0UC, HBN34x0UC, HBN3350UC), section 5.1 Error Code Table

Error code E009
Appliance Oven
Quick answer

E009 is a ROM check error in the user interface. The panel did not receive all of its information from the control module at start-up.

E009 needs a technician on site

E009 points to rom-check fault in the user interface — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

A Bosch wall oven that shows E009 has failed a ROM check in the user interface. In plain terms, when the control panel woke up it asked the relay board for its start-up information and did not receive all of it. The code appears in the error table of Bosch’s service manual for the 300, 500 and 800 Series built-in wall ovens from 2007.

At a glance

Code E009
Appliance Oven
What it means ROM check error in the user interface: it did not receive all information from the control module at start-up.

Reading the description

“ROM” is the read-only memory that holds the board’s stored program. Although the code names the user interface, the manual’s cause column looks beyond the panel. It tells the service tech to check for a loss of communication or a disconnected wire somewhere in the unit. That makes E009 a close cousin of E005: both are about the conversation between the panel and the PC control module at power-up, not about an element or a sensor in the oven cavity.

What an owner can notice

You will not see the wiring without pulling a built-in oven out of the cabinet, which is not an owner job. You can still collect useful details:

  • Does E009 appear every time power is restored, or only now and then?
  • Did it start after a power outage, a breaker trip, or recent work on the oven or the cabinetry around it?
  • Does the display show anything else, such as E005 on another start?

A single breaker cycle is fine to try: off at the panel for 30 seconds, then on. That is the same reset the manual uses after its own procedures. If the code comes back, keep the oven off.

Why the fix may be a connector, not a board

Bosch’s manual tells technicians to disconnect and reconnect each wire and harness on the control module before diagnosing it as bad. With E009 that matters, because the stated cause is a missing signal somewhere in the unit. The control module is reached from the top after sliding the oven about 16 inches out of the wall, and the user interface after about 4 inches.

See also

  • E005: total loss of communication at start-up
  • E010: a data memory error in the same user interface
  • E309: the matching ROM check failure, but in the control module

E009 service for San Francisco wall ovens

Call (415) 851-9513 and say whether E009 is constant or intermittent. Having the model and FD numbers from the plate under the control panel speeds up parts lookup.

Plain language

What this code means

ROM check error in the user interface: it did not receive all information from the control module at start-up.

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair