Skip to content
Error Code

Bosch Wall Oven E101 / E201 Error Code

Source: Service Manual for 300, 500 and 800 Series Built-in Wall Ovens (Bosch HBL8x50UC, HBL57x0UC, HBL56x0UC, HBL54x0UC, HBL35x0UC, HBL33x0UC, HBN56x0UC, HBN54x0UC, HBN35x0UC, HBN34x0UC, HBN3350UC), section 5.1 Error Code Table

Error code E101 / E201
Appliance Oven
Quick answer

E101 and E201 mean the oven temperature sensor reads as an open circuit, E101 for the upper or single cavity and E201 for the lower cavity of a double oven.

E101 / E201 needs a technician on site

E101 / E201 points to cavity 1 temperature sensor open circuit — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

E101 and E201 are the same fault in two different places. Each oven cavity has a temperature sensor, a probe-like part that tells the electronics how hot the cavity is. When the circuit through that sensor reads open, as if a wire were cut, the oven shows E101 for cavity 1 or E201 for cavity 2. Bosch’s service manual for its 2007 300, 500 and 800 Series built-in wall ovens notes that codes beginning with E2 belong to the lower cavity of double ovens.

At a glance

Code E101 / E201
Appliance Oven
What it means The cavity temperature sensor circuit is open: E101 for cavity 1 (upper or single oven), E201 for cavity 2 (lower oven).

Which oven is reporting it

Code Cavity Where you will see it
E101 Cavity 1 Single ovens, or the upper oven of a double
E201 Cavity 2 Lower oven of a double model only

The double ovens in that manual are the 30-inch HBL8650UC, HBL56x0UC and HBL35x0UC and the 27-inch HBN56x0UC and HBN35x0UC. On a single oven only E101 can appear.

What the oven does with an open sensor

The manual’s troubleshooting table describes the behavior: the controls keep working normally, the code appears when the sensor opens, and the cooling fan runs constantly. So a fan that will not stop, together with E101 or E201, is consistent with this fault. Even though the panel still responds, hold off on cooking in that cavity until the sensor circuit has been checked.

Owner steps that are safe

  • Switch the affected oven off. If the fan keeps running, that matches the behavior described above.
  • Restore power with a 30-second breaker cycle, the same reset the manual uses, and see whether the code returns.
  • On a double oven, note which display shows the code. The other cavity has its own sensor.

How a technician confirms it

The sensor is serviceable from inside the cavity, at the front. The manual has the technician check its resistance with an ohmmeter and compare the reading with a chart of normal values by cavity temperature. Service Mode can also display the real-time cavity temperature the control is reading. The sensor’s two wires end at the control module, plug X107 for the upper cavity and X207 for the lower, so a break in the harness can cause the same code as a failed sensor.

E101 and E201 questions

Why is the fan still going with the oven off?
A constantly running cooling fan is part of how Bosch’s table says these ovens behave with an open cavity sensor. Normal run-on after cooking lasts two minutes and then until the cavity cools, so a fan that never stops is worth mentioning.

Would changing the temperature offset help?
No. Bosch lets owners set an offset in the settings menu when food is consistently over- or under-cooked, which shifts the target of a working sensor. It does nothing for a sensor circuit that reads open.

Linked sensor and heat codes

  • E104 / E204: the opposite failure, the same sensor reading shorted
  • E115 / E215: cavity temperature too high while the door is unlocked
  • E118 / E218: cooling fan speed fault, useful to rule out if the fan behaves oddly

Oven sensor service across San Francisco

Call (415) 851-9513 and tell us whether it is E101 or E201. The model number on the plate under the control panel tells us whether you have a single or double oven.

Plain language

What this code means

The cavity temperature sensor circuit is open: E101 for cavity 1 (upper or single oven), E201 for cavity 2 (lower oven).

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair