Skip to content
Error Code

Bosch Wall Oven E118 / E218 Error Code

Source: Service Manual for 300, 500 and 800 Series Built-in Wall Ovens (Bosch HBL8x50UC, HBL57x0UC, HBL56x0UC, HBL54x0UC, HBL35x0UC, HBL33x0UC, HBN56x0UC, HBN54x0UC, HBN35x0UC, HBN34x0UC, HBN3350UC), section 5.1 Error Code Table

Error code E118 / E218
Appliance Oven
Quick answer

E118 (upper or single oven) and E218 (lower oven) are cooling fan supervision errors: the fan speed is too low or too high.

E118 / E218 needs a technician on site

E118 / E218 points to cavity 1 cooling-fan supervision fault — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

Behind the panels of a Bosch built-in wall oven, a cooling fan moves air over the electronics and through the cabinet. The oven does not just switch that fan on; it watches how fast it spins. E118 (upper or single oven) and E218 (lower oven of a double) are the cooling fan supervision errors from Bosch’s service manual for the 2007 300, 500 and 800 Series: the fan speed is too low or too high.

At a glance

Code E118 / E218
Appliance Oven
What it means Cooling fan supervision error, fan speed too low or too high: E118 for cavity 1 (upper or single oven), E218 for cavity 2 (lower oven).
First thing to try Make sure the wire harness is not touching the fan motor or pinched.

How the oven knows the fan speed

Each cooling fan in these ovens is a two-speed, 120-volt motor with three terminals (high, low and neutral) and a Hall effect sensor, a small magnetic sensor that counts rotation. If that sensor does not detect the fan turning, the oven raises the error. The manual’s test table describes the timing: the oven accepts cooking modes as usual, and about 45 seconds later E118 appears on the upper display, or E218 on the lower one.

Things you can notice without opening anything

  • When the code appears, listen near the top and vents of the oven. Is the fan running, silent, or making a scraping or ticking sound?
  • Remember that the cooling fan normally keeps running after you switch the oven off: two minutes regardless of temperature, then until the cavity has cooled to a set point. Running after shut-off is not a fault by itself.
  • Note whether the code follows a specific mode or appears in any mode about 45 seconds after starting.

Switch the oven off if the code appears. Running the oven while its electronics cooling is in doubt is not worth the risk.

Service checklist from Bosch

For E118 and E218 the manual gives an unusually specific list of mechanical checks before any part is blamed:

  1. Make sure the wire harness is not touching the fan motor or pinched.
  2. Confirm the plenum (the sheet metal air channel) is not touching the fan end cap.
  3. Check the Hall effect sensor connection.
  4. Test the fan at the control module, where the manual has the technician measure voltage on the fan’s high and low speed pins.

The upper fan is removed from the top and rear of the unit with the oven pulled fully out of the wall, so even the first two checks are not owner work on a built-in oven.

Cooling fan or convection fan?

These are two different motors. The convection fan sits behind a baffle on the rear wall of the cavity and circulates hot air around the food in convection modes. According to the manual’s test table, a convection motor failure produces no fail code at all. E118 and E218 are about the cooling fan that serves the electronics and cabinet, not the fan you can see inside the oven.

Codes that often get looked at together

  • E303: the control module itself running above 212°F
  • E003: the user interface electronics above 185°F
  • E101 / E201: open oven sensor, a fault where the manual says the cooling fan runs constantly

Cooling fan service for Bosch ovens in San Francisco

Call (415) 851-9513 and tell us what you hear from the fan when E118 or E218 shows. Your model number from under the control panel tells us whether you have a single or a double oven.

Plain language

What this code means

Cooling fan supervision error, fan speed too low or too high: E118 for cavity 1 (upper or single oven), E218 for cavity 2 (lower oven).

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair