Skip to content
Error Code

Bosch Wall Oven E124 / E224 Error Code

Source: Service Manual for 300, 500 and 800 Series Built-in Wall Ovens (Bosch HBL8x50UC, HBL57x0UC, HBL56x0UC, HBL54x0UC, HBL35x0UC, HBL33x0UC, HBN56x0UC, HBN54x0UC, HBN35x0UC, HBN34x0UC, HBN3350UC), section 5.1 Error Code Table

Error code E124 / E224
Appliance Oven
Quick answer

E124 (upper or single oven) and E224 (lower oven) are door switch errors: the control cannot tell whether the door switch is open or closed.

E124 / E224 needs a technician on site

E124 / E224 points to cavity 1 door-switch fault — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

Every Bosch built-in wall oven needs to know whether its door is shut. On the 2007 300, 500 and 800 Series models, that job belongs to a door switch built into the motorized door latch assembly. E124 (upper or single oven) and E224 (lower oven of a double) mean the switch is in an undefined state: the signal reaching the control does not make sense as either “open” or “closed.”

At a glance

Code E124 / E224
Appliance Oven
What it means The door switch is in an undefined state: E124 for cavity 1 (upper or single oven), E224 for cavity 2 (lower oven).

Where the door switch lives

Bosch’s service manual describes the latch assembly as having two switches. One is the door switch. The other reports whether the latch is locked or unlocked. Both are wired back to the PC control module, the upper cavity through plug X106 and the lower through X206. According to the manual’s test table, if the latch position is not detected during normal operation, the oven shows E124 or E126 on the upper side, or E224 or E226 on the lower. Because they share one assembly and one plug, the door switch and latch codes are checked together.

What you can watch for

You cannot see the switch, but you can notice how the oven reacts to the door. The manual states that the cavity lights come on whenever the door is opened and go off when it closes. If that has stopped happening on the cavity with the code, mention it when you call. Also check that the door closes fully and evenly, with nothing caught in it. Do not adjust the hinges or remove trim around the latch to look for the switch.

Repair path

  1. A breaker reset (30 seconds off) is a safe first test; note whether the code returns.
  2. If it does, a technician follows the wiring diagram in the oven’s Service Guide, which Bosch packs inside the unit on the underside of the upper plenum access panel.
  3. Because the door switch is part of the latch assembly, and Bosch services that assembly as one piece, a failed switch means a new latch assembly.

FAQ on E124

Is my door actually open?
Not necessarily. The code says the control cannot read the switch reliably, which is different from reporting the door open.

Does E224 mean both ovens have a problem?
No. Codes starting with E2 apply to the lower cavity of a double oven, which has its own latch and switch.

Can I still use the oven?
The manual does not say what the oven allows while E124 or E224 is showing. Hold off on self-clean, which depends on the latch assembly, until it has been checked.

Door and latch codes

Door switch service in San Francisco

Call (415) 851-9513 and tell us which cavity shows the code and whether the oven light still follows the door.

Plain language

What this code means

The door switch is in an undefined state: E124 for cavity 1 (upper or single oven), E224 for cavity 2 (lower oven).

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair