Skip to content
Error Code

Bosch Wall Oven E104 / E204 Error Code

Source: Service Manual for 300, 500 and 800 Series Built-in Wall Ovens (Bosch HBL8x50UC, HBL57x0UC, HBL56x0UC, HBL54x0UC, HBL35x0UC, HBL33x0UC, HBN56x0UC, HBN54x0UC, HBN35x0UC, HBN34x0UC, HBN3350UC), section 5.1 Error Code Table

Error code E104 / E204
Appliance Oven
Quick answer

E104 and E204 mean the cavity temperature sensor reads as shorted. E104 is the upper or single oven; E204 is the lower oven of a double.

E104 / E204 needs a technician on site

E104 / E204 points to cavity 1 temperature sensor short circuit — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

A shorted oven sensor hands the electronics a reading they cannot use. On Bosch 300, 500 and 800 Series built-in wall ovens (the 2007 HBL and HBN line), that condition shows as E104 in the upper or only cavity, and as E204 in the lower cavity of a double oven.

At a glance

Code E104 / E204
Appliance Oven
What it means The cavity temperature sensor reads shorted: E104 for cavity 1 (upper or single oven), E204 for cavity 2 (lower oven).

Shorted versus open

The temperature sensor is the part mounted in the oven cavity whose resistance changes with heat. The control reads that resistance to decide when to cycle the elements. Bosch’s manual has two codes for a sensor that stops making sense:

  • Open (E101 / E201): no circuit at all.
  • Shorted (E104 / E204): the circuit reads as if the two sensor wires were touching.

In both cases the reading from that cavity is not usable. The troubleshooting table says the controls still respond and the cooling fan stays on constantly while the fault is present. That fan is something you can notice from outside the oven.

Upper cavity or lower?

The manual states that error codes beginning with E2 apply to the lower cavity of double ovens. Its double-oven models are HBL8650UC, HBL56x0UC, HBL35x0UC, HBN56x0UC and HBN35x0UC. If your oven is one of the single models, E204 should not appear, and E104 refers to the only cavity.

What not to do

Do not keep cooking in the cavity that shows the code until it has been checked. Do not open panels or unplug harnesses to look for the short. The sensor wiring runs to the control module in the top of the unit, and testing it is technician work. A 30-second breaker reset is fine, and if the code returns, leave that oven off.

On the service visit

The sensor itself comes out from the front, inside the cavity. A technician measures its resistance with an ohmmeter against Bosch’s table of normal values, compares the result with the live temperature shown in Service Mode, and checks the harness to plug X107 (upper) or X207 (lower) on the control module. The sensor and its wiring form one circuit, so both get checked before a part is replaced.

For the live reading, the manual has the technician step through Service Mode with FAST PREHEAT on HBL8 and HBL5/HBN5 models until the oven temperature item appears, or with the TEMP key on HBL3/HBN3 models. That number gives a second reading to compare with the ohmmeter result.

Why the manual says “Cvt 1”

Bosch’s error table abbreviates the cavities as Cvt 1 and Cvt 2. Cavity 1 is the upper oven, or the only oven on a single model; cavity 2 is the lower oven. That is the whole difference between E104 and E204.

Codes in the same family

  • E101 / E201: the sensor circuit reading open
  • E115 / E215: temperature too high in an unlocked cavity
  • E303: control module electronics above 212°F

Shorted sensor repair in San Francisco

Call (415) 851-9513 and say which display shows E104 or E204. Tell us if the cooling fan has been running nonstop.

Plain language

What this code means

The cavity temperature sensor reads shorted: E104 for cavity 1 (upper or single oven), E204 for cavity 2 (lower oven).

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair