Skip to content
Error Code

Bosch Wall Oven E116 Error Code

Source: Service Manual for 300, 500 and 800 Series Built-in Wall Ovens (Bosch HBL8x50UC, HBL57x0UC, HBL56x0UC, HBL54x0UC, HBL35x0UC, HBL33x0UC, HBN56x0UC, HBN54x0UC, HBN35x0UC, HBN34x0UC, HBN3350UC), section 5.1 Error Code Table

Error code E116
Appliance Oven
Quick answer

E116 is a meat probe error. Bosch's service manual notes that the standard probe module is built into the control module.

E116 needs a technician on site

E116 points to cavity 1 meat-probe fault — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

Some Bosch built-in wall ovens come with a meat probe, a thermometer on a cable that plugs into the cavity wall so the oven can cook to an internal food temperature. E116 is the general probe error for those ovens in Bosch’s service manual for the 2007 300, 500 and 800 Series. The manual adds one note that shapes the repair: the standard probe module is part of the control module.

At a glance

Code E116
Appliance Oven
What it means Probe error; the standard probe module is part of the control module.
First thing to try Turn the oven off and let it cool before handling the probe or its socket.

What “part of the control module” means

There is no separate probe circuit board to swap. The electronics that read the probe live on the PC control module, the relay board in the top of the oven that also runs the elements, fans, lights and latch. The probe itself, its receptacle in the cavity and the wire harness back to that board make up the rest of the circuit. The manual points technicians to a wiring diagram in the oven’s Service Guide for this code.

Does your oven use a probe?

The manual’s plug table shows the meat probe connector on the control module marked not used on HBL3 and HBN3 models. So the probe codes are relevant to the other models in that line. If you have never used a probe, note that when you call.

Owner checks

  1. Turn the oven off and let it cool before handling the probe or its socket.
  2. Unplug the probe from the receptacle and look at the cable and plug for obvious damage such as kinks, crushed spots or burn marks.
  3. Restore the oven with a 30-second breaker reset.
  4. Note whether E116 returns with the probe unplugged, or only when it is plugged in.

Do not open the receptacle or chase the harness behind the oven wall.

Where service goes next

Since the probe electronics are on the control module, a confirmed fault there means work on that board, which is reached through the top access panel with the oven slid out of the wall. The manual asks technicians to reseat every wire and harness before condemning the module, and to reset and test the oven after replacing it.

Other probe codes

  • E122: probe reading too high or shorted
  • E123: probe reading too low
  • E309: ROM check failure on the same control module

Bosch meat probe repair in San Francisco

Call (415) 851-9513 and tell us whether E116 shows with the probe unplugged. The model number under the control panel tells us if your oven has the probe connector at all.

Plain language

What this code means

Probe error; the standard probe module is part of the control module.

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair