Skip to content
Error Code

Bosch Washer E17 / F17 / F29 Error Code

Source: Bosch US Owner Support - Washer Error Codes

Error code E17 / F17 / F29
Appliance Washer
Quick answer

Not enough water is reaching the washer. Clean the filters in the supply hose and check the tap's flow rate.

A Bosch washer that stops with E17, F17 or F29 is not getting enough water. Bosch lists all three under one meaning: the filters in the water connection or in the AquaStop hose are blocked, or the household water pressure is too low.

At a glance

Code E17 / F17 / F29
Appliance Washer
What it means The filters in the water connection or AquaStop hose are blocked, or the water pressure is too low.

Before you unscrew anything

Many Bosch washers use an AquaStop supply hose. Bosch warns that the AquaStop safety device contains an electric valve, so it must not be immersed in water while you clean it. Rinse and brush the filter only, keeping the valve housing dry.

Cleaning the supply-hose filters

  1. Turn the water tap off.
  2. Unscrew the hose from the tap.
  3. Clean the filter in the hose end with a small brush.
  4. No AquaStop? Then also take the hose off the back of the washer, pull the filter out of the inlet with pliers, and clean it the same way.
  5. Reconnect the hose and check both joints for leaks.
  6. Open the tap fully.

Putting the hose back

Bosch’s WAT28400UC manual adds a few reassembly details. Both ends of the supply hose need their rubber washers in place, since a missing washer causes leaks. Tighten the connections by hand only. The connection points sit under full water pressure, so turn the tap on and check the joints for leaks. If the hose shows cuts, kinks or leaks, the manual says to replace it with a new one.

The flow test that settles it

Bosch gives a simple benchmark: with the tap fully open, roughly 2.5 gallons (10 liters) of water per minute must flow out. Hold a bucket marked at a known volume under the open tap (hose removed) and time it. If clean filters still leave you well short of that rate, the supply is the limit, and Bosch’s advice is to contact a plumber about the water pressure.

Who fixes what

What you find Next step
Grit or scale in a hose filter Clean it, reconnect, rerun the program
Filters clean, tap flow well under 2.5 gal/min Plumber, for household water pressure
Filters clean, flow fine, code returns Appliance technician

Common questions about E17

Can I soak the AquaStop end to loosen the scale?
No. Bosch specifically says not to immerse it because of the electric valve inside. Brush the filter instead.

Is F29 a different problem?
No. Bosch groups E17, F17 and F29 under the same cause and the same fix.

Related supply-side codes

  • E:92-01: the same low-pressure or blocked-filter cause in the newer code format.
  • E:30-10: filling fault that also covers a closed faucet or kinked inlet hose.
  • E23 / F23: the AquaStop system itself has been triggered.

San Francisco Bosch washer repair

Done the filters and the flow test? Call (415) 851-9513 and tell us the code and the flow you measured. Having the model number to hand makes it easier to match parts.

Plain language

What this code means

The filters in the water connection or AquaStop hose are blocked, or the water pressure is too low.

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair