Skip to content
Error Code

Bosch Washer E:30-10 Error Code

Source: Bosch US Owner Support - Washer Error Codes

Error code E:30-10
Appliance Washer
Quick answer

The washer is not filling correctly. Check the faucet, inlet hose and filters, then reset; a level-system fault needs a technician.

E:30-10 needs a technician on site

E:30-10 points to low water pressure, blocked inlet filters, closed tap, kinked inlet hose, or water-level measurement fault — an internal part that can’t be checked or fixed safely from the outside. A restart may hide it for a while, but the cause stays. Our technician tests it on site and confirms the fault before any part is replaced.

E:30-10, sometimes shown together with a faucet icon, is a filling fault. Bosch lists five possible reasons on its owner-support page. Four of them are on the supply side and easy to check. The fifth is inside the washer.

At a glance

Code E:30-10
Appliance Washer
What it means The washer could not fill correctly because of low water pressure, blocked inlet filters, a closed faucet, a kinked or jammed inlet hose, or a defective water level measurement system.
First thing to try Wait about 5 minutes, until the draining process has ended.
When to call a technician Check the faucet, inlet hose and filters, then reset; a level-system fault needs a technician.

Five causes, from easiest to hardest

Cause Bosch lists What to do
The faucet is turned off Turn it on, all the way.
The inlet hose is kinked or jammed Pull the washer out enough to straighten the hose. Make sure it isn’t pinched against the wall.
The filters in the water inlet are blocked Clean the filters in the water inflow.
Water pressure is low Contact a plumber. This is a household supply issue.
The water level measurement system is defective Run the reset below. If it fails, book a technician.

The reset, done in the right order

Bosch is specific here, and the order matters because the washer may still be pumping out water when the code appears:

  1. Wait about 5 minutes, until the draining process has ended.
  2. Switch the appliance off to reset the fault message.
  3. Switch it back on.
  4. If the message comes up again, book a technician.

What the “water level measurement system” is

A washer has to know how full the drum is before it can stop filling and start washing. That reading comes from a level-sensing system. If the faucet is open, the hose is straight, the filters are clean and the pressure is fine, a repeat E:30-10 points toward that system. Since it sits inside the cabinet, it is not something to open up yourself.

Quick answers

The faucet icon is lit but the tap is open. What now?
Work down the table. A kinked hose or clogged inlet filter can starve the washer even with the tap fully on.

Why wait five minutes before switching off?
Bosch’s reset steps start with letting the draining finish, so that is the first step to follow.

Codes on the same supply line

  • E:92-01: low pressure or blocked inlet filters only, with no level-system cause.
  • E17 / F17 / F29: inlet filter cleaning with the AquaStop caution and a flow test.
  • E26 / F26: the analogue pressure sensor, a level-sensing part, reported as faulty.

Bosch washer fill problems: service in San Francisco

Call (415) 851-9513 if E:30-10 is still there after the five-minute reset. Tell us whether the faucet icon was showing and which supply checks you have done.

Plain language

What this code means

The washer could not fill correctly because of low water pressure, blocked inlet filters, a closed faucet, a kinked or jammed inlet hose, or a defective water level measurement system.

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair