Skip to content
Error Code

Bosch Dishwasher E32-00 Error Code

Source: Bosch Dishwasher SMS6HCW01A User manual (aus), Troubleshooting: Error code / Fault display (doc 9001547345_A)

Error code E32-00
Appliance Dishwasher
Quick answer

A water supply fault. Bosch's manuals list a kinked supply hose, a closed or furred-up tap, and a blocked inlet filter.

On Bosch dishwashers with a four-digit display, E:32-00 (also written E3200) lights up alternately with the normal readout when the machine is not getting water the way it should. Some models light the water supply indicator instead of showing the number. Bosch’s owner manuals treat it as a supply problem on the house side, and every cause they list can be checked without opening the dishwasher.

At a glance

Code E32-00
Appliance Dishwasher
What it means The dishwasher is not getting enough water because the supply hose is kinked, the tap is off, jammed or furred up, or the filter in the supply or AquaStop hose connection is blocked.
First thing to try Switch off the dishwasher.

Causes listed in the Bosch manuals

  • The supply hose is kinked.
  • The water tap is turned off.
  • The water tap is jammed or furred up with scale.
  • The filters in the water connection of the supply hose or AquaStop hose are blocked.

Bosch also gives a minimum flow: with the supply open, water should come through at at least 10 liters per minute, roughly 2.6 gallons. A valve that is only partly open, or one that has seized with scale, can fall short of that.

Quick checks first

Look under the sink for the valve that feeds the dishwasher and make sure it is fully open. If it has been off for a while or turns stiffly, it may be jammed. Then trace the supply hose as far as you can and make sure it has no kinks. Bosch’s instruction is simply to install the hose without kinks.

Cleaning the inlet filter

A small filter sits in the threaded connection where the hose meets the water supply. Bosch’s sequence for cleaning it:

  1. Switch off the dishwasher.
  2. Pull out the mains plug.
  3. Turn off the water tap.
  4. Unscrew the water connection. Have a towel ready, as some water will be in the hose.
  5. Remove the filter from the supply hose.
  6. Clean the filter.
  7. Put the filter back into the supply hose.
  8. Screw the water connection back on.
  9. Check the connection for leaks.
  10. Restore power.
  11. Switch the dishwasher on.

Step 9 is easy to skip and worth doing. Open the tap and watch the fitting for a minute before you close the cabinet. A threaded connection that was not screwed back on squarely can drip slowly, and a slow drip under a sink can go unnoticed. If the fitting will not seal, close the tap again and leave it for a technician.

What an AquaStop hose is

Some Bosch dishwashers use an AquaStop supply hose, a supply hose whose plastic housing contains an electric safety valve; Bosch warns never to immerse that housing or cut the hose. The filter cleaning above applies to its water connection too. If the AquaStop housing itself is cracked or wet, leave it alone and call for service.

Codes that sit close to E32-00

Water supply repair for Bosch dishwashers in SF

If the tap, hose and filter all check out, call (415) 851-9513. The E-Nr and FD numbers are on the rating plate inside the door; read them to us when you call.

Plain language

What this code means

The dishwasher is not getting enough water because the supply hose is kinked, the tap is off, jammed or furred up, or the filter in the supply or AquaStop hose connection is blocked.

Ready to get your Bosch appliance working again?

Book a repair online or call us — clear estimates and approval before any repair work begins.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area San Francisco Bay Area, California

Request your repair

(415) 851-9513 Book a Repair